← All services

Ceiling Fan Installation

Residential ceiling fan installation and replacement — fan-rated box, proper switching, and sizing by room across Utah County and the Wasatch Front.

Overview

Fan-rated boxes, proper switching, and sized-for-the-room ceiling fan installs across Utah County and the Wasatch Front

A ceiling fan looks like a simple swap until you open the ceiling. The piece that trips up a lot of DIY installs — and plenty of handymen — is the electrical box. A standard round or octagonal box isn't rated to carry the weight of a fan, let alone the ongoing torque of a motor that runs for hours at a time. NEC requires a fan-rated box (listed and marked for ceiling fan support) for any installed fan. If your ceiling has a plain lighting box up there, we swap it for a fan-rated one before anything else happens.

Replacing an existing fan is usually a one-visit job: we verify the box is fan-rated (older houses in Orem, Provo, and Pleasant Grove often aren't), update the wiring if the new fan has different control requirements, mount the new unit, and balance it. New installs in a room that doesn't currently have overhead wiring are a bigger scope — we're fishing a switched hot through the wall and ceiling to a new fan-rated box, which means some drywall work and sometimes a new wall switch location. Either way, we walk the ceiling and the switch wall first so you know what you're signing up for.

Sizing matters more than people realize. A 42-inch fan in a 15-by-18 primary bedroom will move air in a two-foot bubble under the fan and leave the rest of the room still. A 60-inch fan in a 10-by-10 guest room will beat you to death with wind. The rough rule we use: 36-44" for rooms up to 100 square feet, 52" for rooms 100-200 square feet, 60-72" for rooms above 200 square feet or vaulted ceilings. On great rooms over 400 square feet, we often recommend two medium fans instead of one giant one.

Ceiling height drives downrod selection. On a standard 8-foot ceiling, the fan body wants to hang about 7-8 feet off the floor — a flush-mount or 3-6 inch downrod is usually right. On a 10-foot ceiling, you want a 12-18 inch downrod. On a vaulted ceiling in a Heber or Alpine great room, we're often hanging 24-48 inches with a sloped-ceiling adapter so the fan sits level under a 20-foot peak. We bring the right downrod to the install so there's no second trip.

Switching is where a lot of modern upgrades land. If you're replacing a pull-chain fan, you can keep the pull chains or install a wall control. Smart options have gotten good — Lutron Caséta fan speed controls, Hampton Bay and Hunter Wi-Fi fans with their own apps, and Alexa/HomeKit/Google integration are all realistic. If your room doesn't have a switched hot wire to the ceiling (common in older bedrooms built as "receptacle-only"), we'll pull a new one and add the wall switch — the fan can't be smart if there's no circuit to control.

When to call us

Signs it’s time.

You bought a new fan and the old box isn't fan-rated

Standard lighting boxes aren't built to carry a fan's weight plus running vibration. We swap in a listed fan-rated box so the install is actually safe to use.

You want a fan in a room that doesn't have overhead wiring

Older bedrooms sometimes have no ceiling light at all. We fish a new switched circuit from the wall switch, add a fan-rated box, and tie it in.

Vaulted or sloped ceiling in a great room

Vaulted ceilings in Alpine, Heber, Mapleton need a sloped-ceiling adapter, the right downrod length, and often a longer blade span. We size it to the room.

You want a smart or remote-controlled fan

Lutron Caséta, Alexa, HomeKit, or app-controlled fans need the right switching infrastructure. We wire for the control scheme before the fan goes up.

How we do it

Our process, step by step.

No mystery, no sales games. Here’s exactly what happens from the first phone call to the final inspection.

    1

    Confirm scope on the phone or in-person

    Tell us the room size, ceiling height, whether there's an existing fan or light fixture up there, and whether you've bought the fan yet. For replacements we can often quote off photos; for new installs in rooms without overhead wiring we come walk the space to confirm the wire path.

    2

    Verify the box and switching setup

    On arrival, we pull the existing fixture or box and check whether it's fan-rated and solidly anchored. We also check the wall switch — is there a switched hot already? If the fan requires a smart control, do we have a neutral at the switch box? Any gaps we find get addressed as part of the install.

    3

    Install the fan-rated box (if needed)

    If the existing box isn't fan-rated, we remove it and install a listed fan-rated box anchored to the ceiling joist or a fan-rated brace bar between joists. This is the step most DIY installs skip — and it's the one that keeps the fan from eventually working itself loose.

    4

    Run new wiring (if the room is new to overhead power)

    For bedrooms or rooms without overhead circuits, we fish a new switched hot wire from the wall switch through the wall, across the attic or ceiling joists, and down to the new fan box. For smart controls, we also verify we have a neutral at the wall switch and add it if needed.

    5

    Assemble and mount the fan at the right downrod

    We size the downrod to your ceiling height, use a sloped-ceiling adapter if the ceiling is vaulted, assemble the fan canopy and motor on the ground (safer and faster than overhead), then mount to the fan-rated box. Blades go on last and get checked for balance.

    6

    Wire the control (pull-chain, wall switch, remote, or smart)

    Standard pull-chain is the simplest. For wall-switch control, we wire the fan's hot to the switched hot. For remote-controlled fans, we install the receiver in the canopy and pair it with the handheld. For Lutron Caséta, Alexa-compatible, or HomeKit setups, we install the fan-speed-rated switch at the wall and pair everything before we leave.

    7

    Test, balance, and walk you through

    We run the fan at all speeds, verify direction (downdraft for summer cooling, updraft for winter heat distribution), balance any blade wobble with the included weights, and walk you through controls — including how to swap seasonal direction and how to re-pair a remote if it ever disconnects.

What’s included

Our scope for this job.

  • Fan-rated listed ceiling box installed if the existing box isn't rated for a fan
  • Downrod length matched to your ceiling height (standard 8ft, 10ft, or vaulted)
  • Wall switch, pull-chain, remote receiver, or smart/Wi-Fi control wired per the fan's manual
  • New switched hot wire run from the wall if the room has no overhead circuit
  • Blade sizing recommendation based on room square footage before you buy the fan
  • Blade balance, direction verification (summer downdraft vs winter updraft), and operation check before we leave
  • Permit and inspection for new-install work where the city requires it
Common questions

What people ask about ceiling fans.

Do I actually need a fan-rated box, or will my regular ceiling box hold it?

You need a fan-rated box, full stop. Standard lighting boxes aren't designed for the weight and ongoing torque of a motor, and they can loosen or pull free over time — which means a 20-pound fan coming down from your ceiling. NEC requires a listed fan-rated box for every installed ceiling fan. We swap in the correct box every time; it's part of the install, not an upcharge.

What size fan do I need for my room?

Rough rule: 36-44 inches for rooms up to 100 square feet (small bedrooms, bathrooms), 52 inches for rooms 100-200 square feet (standard bedrooms, dining rooms), 60-72 inches for rooms over 200 square feet or with vaulted ceilings. For great rooms above 400 square feet, two medium fans often work better than one oversized one. We'll measure your room and tell you honestly before you buy.

I bought the fan myself — can you install it?

Yes, that's most of what we install. Just make sure it's UL-listed (anything from Home Depot, Lowe's, Hunter, Hampton Bay, Minka Aire, Casablanca is fine) and keep the manual and all the small parts in the box. If you haven't bought one yet, we're happy to recommend what we see hold up well in Utah homes — not every brand is created equal on bearings and remote reliability.

What's the install cost?

It depends on whether the existing box is fan-rated, whether we need to run a new switched hot wire (common in older bedrooms), what the ceiling height is, and whether you want standard pull-chain, wall switch, or smart control. Simple replacement of an existing fan is one scope; new install into a room with no overhead wiring is a bigger scope. We walk the room and quote firm — no "from $X" that balloons at the end.

Do I need a permit for a ceiling fan?

For a pure replacement (existing fan-rated box, existing switched circuit, swapping one fan for another), most Utah cities don't require a permit. For a new install that involves adding a fan-rated box, running new wiring, or adding a wall switch, many cities do require a permit — we handle it and schedule the inspection where it applies. We'll tell you which bucket your job is in.

What's the right downrod length?

Fan body should hang about 7-8 feet off the finished floor for best airflow. On a standard 8-foot ceiling that means a flush mount or very short downrod (3-6 inches). On a 10-foot ceiling, a 12-18 inch downrod. On vaulted 14-20 foot ceilings common in Alpine and Heber great rooms, we're often running 24-48 inch downrods with sloped-ceiling adapters. We bring the right downrod to the install so the first attempt is the only one.

Can I use my fan outside on a covered patio?

Only if the fan is damp-rated (for covered outdoor spaces where it won't see direct rain) or wet-rated (for fully exposed outdoor spaces). A standard indoor fan put outside will rust bearings and short out the motor within a season — Utah winters are especially rough on them. Check the UL listing on the box; it'll say "indoor," "damp-rated," or "wet-rated." We'll verify before install and tell you if what you bought isn't the right rating.

My bedroom doesn't have a ceiling light — can I still get a fan?

Yes, but it's more work than a simple swap. We're pulling a new switched hot wire from the room's wall switch (or adding a new wall switch if there isn't one) up through the wall, across the attic or ceiling, and down to a new fan-rated box in the ceiling. Older houses in Springville, Provo, and Payson are often built this way — the receptacles work off a wall switch but the ceiling has no circuit. One or two days of work depending on ceiling access.

Can you install a smart ceiling fan with Alexa or HomeKit?

Absolutely. The most reliable setups we install are Hunter and Hampton Bay Wi-Fi fans (built-in Alexa/Google compatibility), Lutron Caséta fan controls (works with any fan motor), and SwitchBot or Bond-style retrofit modules on existing fans. The gotcha: most smart fans need a constant hot and a neutral at the switch box, which some older houses don't have. We check your switch wiring before quoting a smart install.

How long does a ceiling fan install take?

A straightforward replacement with an existing fan-rated box is usually 60-90 minutes. A swap that requires installing a fan-rated box and new wiring at the ceiling is typically two to three hours. A full new install in a room with no overhead wiring is a half-day to a full day depending on attic access, ceiling finish, and switch wiring. We give you a realistic time estimate when we quote.

We serve Salt Lake County, Utah County, Wasatch County, Davis County from our Springville base. See all service areas →

Need an electrician for your Utah home?

Panel upgrades, EV chargers, generators, aluminum wiring, remodels, and everything in between — from a licensed, family-run team that takes the time to explain what we’re doing.

(801) 348-9201
Schedule Estimate