Commercial & Server-Room Dedicated Circuits
Dedicated 20A/30A isolated-ground circuits for server racks, telecom closets, point-of-sale terminals, medical equipment, and professional workshops. NEC Article 645 compliant.
Commercial dedicated circuits, isolated-ground runs, server rooms, and franchise tenant improvements
Commercial dedicated circuit work is where small businesses meet real code requirements. We've done the electrical for Perspire Sauna Studio franchise locations in Sandy and Bluffdale, a golf studio in Saratoga Springs, and a handful of small-office and retail TI buildouts. Our scope is the electrical side — dedicated circuits for infrared saunas, 240V golf simulator and launch monitor circuits, POS stations, back-office server racks, HVAC make-ready — but we don't do low-voltage, structured cabling, or data drops. That's a different trade and we'll tell you honestly rather than fake it.
Server rooms and sensitive equipment benefit from isolated-ground circuits per NEC 647 (where applicable) and dedicated grounding — we handle that infrastructure. If you're on a shared panel in a strip center, we coordinate with the property's electrical setup and the city on permits for any new load.
Franchise TI work is a specific muscle. The brand sends a plan set — electrical, mechanical, lighting — and we build to spec. On Perspire Sauna buildouts we're wiring dedicated circuits for each infrared sauna cabin (typically 20A each, sometimes 30A depending on cabin spec), make-up air and exhaust fans, ambient lighting on dimmers, POS, and the back-office network closet (power only — the low-voltage sub handles data). The timeline is usually tight because the franchise has an opening date; we read the plan set early and flag any questions before demo so there's no mid-job scope surprise.
Server rooms, networking closets, and sensitive-equipment spaces fall under NEC 645 (information technology equipment) for scope and NEC 647 for isolated ground where it's actually warranted. A small retail or office server rack typically wants two dedicated 20A circuits (one per PDU for redundancy), proper equipment grounding, surge protection, and a dedicated circuit for the mini-split keeping the room cool. We handle all of that. We do not run Cat6, terminate RJ45, or do rack cable management — that's structured cabling and it's licensed separately in Utah.
Caddis is a family-run Springville shop. On commercial work, that means you talk to the owner (Tyler) or the lead electrician on your job — not a project manager you'll never meet again. We're small enough to be honest when a job isn't a fit for our crew size, and we'll tell you so rather than overcommit. For the TI work we do take on, we show up when we said we would and we hand off clean documentation at closeout.
Signs it’s time.
Franchise fit-out requires brand-spec electrical
Infrared sauna franchises, fitness concepts, and food franchises almost always come with a brand electrical spec. We read the plan set, flag questions early, and build to spec.
New POS, kiosk, or payment terminal install
Payment terminals shouldn't be on a shared circuit with the espresso machine. Dedicated 20A circuits, often with surge protection, keep card processing stable.
Server room or networking closet going in
A small server rack usually wants two dedicated 20A circuits (one per PDU for redundancy), proper grounding, and a dedicated circuit for the mini-split keeping the room cool.
Equipment upgrade needs more amps than the circuit was built for
New commercial oven, new sauna heater, upgraded HVAC — if the nameplate exceeds the existing breaker, we don't just upsize the breaker (that's dangerous). We pull the right wire for the new load.
Our process, step by step.
No mystery, no sales games. Here’s exactly what happens from the first phone call to the final inspection.
Plan review or site walk
For franchise TI work, we read the brand's plan set and spec, flag questions, and attend any pre-con meetings the GC runs. For non-franchise work (owner-direct TI, equipment upgrades, server room buildouts), we walk the space, inventory the existing electrical, and talk through what you need.
Scope and firm written quote
You get a line-item quote covering circuits, panel work, outlets and devices, permit, inspection, and any coordination with property management. For plan-set jobs we quote off the drawings. For walkthroughs we quote off the measurement sheet we leave with you.
Permit and property coordination
We pull the electrical permit under our license, coordinate with your landlord on any shared infrastructure (main panel access, service upgrades, after-hours work), and schedule inspections. For strip-center TI work we often coordinate with the property manager on timing to avoid disrupting neighboring tenants.
Rough-in or circuit installation
For TI with framing in progress, we show up for rough-in after framing is up — boxes, home runs, panel work. For retrofits in existing suites, we install the new circuits around existing ceilings and walls, running conduit or MC cable per code and property requirements.
Trim-out and equipment hook-up
Devices (receptacles, switches, dimmers), light fixtures, dedicated-circuit terminations at equipment, surge protection on sensitive circuits, isolated-ground connections where specified. We coordinate with your equipment installer (sauna installer, golf sim installer, POS vendor) on final hook-up timing.
Inspection and closeout
City inspector signs off at rough-in and final. We walk the space with you (and your GC if applicable), verify everything functions, test GFCI and AFCI protection, and hand off as-built documentation — permit sign-off, circuit directory, equipment hook-up spec sheets.
Our scope for this job.
- Dedicated 120V 20A circuits for POS, payment terminals, workstations
- 240V dedicated circuits for commercial equipment per manufacturer nameplate
- Isolated-ground circuits for sensitive electronics per NEC 647 where specified
- Server-room electrical infrastructure per NEC 645 scope (power, not low-voltage)
- Franchise brand-spec compliance — we work from the plan set
- Coordination with property management and city on panel upgrades or sub-panel adds
- Permit, inspection, and as-built documentation handed off at closeout
What people ask about commercial circuits.
Do you do data, network, and low-voltage cabling?
No. We're licensed for line-voltage electrical — power circuits, panels, lighting. Structured cabling, data drops, access control, and AV are their own trade and licensure. We'll happily recommend low-voltage contractors we've worked alongside on previous builds.
What kind of commercial work have you actually done?
Perspire Sauna Studio franchise locations in Sandy and Bluffdale (infrared sauna power, mechanical makeup, lighting), a golf studio in Saratoga Springs (simulator and launch monitor circuits), and a handful of smaller retail and office tenant improvements across Utah County and the Salt Lake Valley. We're a small crew — we're honest about taking on jobs that fit our size.
What's an isolated-ground circuit and do I need one?
An isolated-ground circuit runs the equipment grounding conductor straight back to the panel ground bar, bypassing the conduit as a ground path. It reduces electrical noise on sensitive equipment — think recording studios, medical imaging, some audio-video setups. For most POS and office equipment, standard grounding plus surge protection is enough. We'll tell you honestly whether your equipment actually benefits.
Can you work on my space in a shared retail building?
Yes, as long as we have access to the panel serving your suite and we can coordinate with property management on any work that touches shared infrastructure. If your service is undersized for your buildout, we'll flag it and work with the landlord on the fix.
How does commercial pricing work?
Scope-based, quoted off the plan set or a site walk. For TI work, we read the drawings, confirm what the brand or landlord requires, and give you a line-item quote. We don't do "T&M, we'll see where it lands" on commercial — you get a number and we hold to it.
What's your typical turnaround for a TI electrical scope?
Depends entirely on size. A small POS and lighting retrofit in an existing suite is often a one-week job. A full franchise fit-out with new circuits, panel work, HVAC make-ready, and lighting is three to six weeks of electrical, usually spread across a longer overall GC schedule. We give you a realistic schedule during the quote so your opening date isn't a surprise.
Do you work with my general contractor or go direct to me?
Both. For straightforward TI work we often go direct to the business owner or franchisee. For larger scopes with multiple trades (framing, plumbing, HVAC, drywall, flooring), we're used to being the electrical sub under a GC's schedule. The main thing is one person owning the schedule — we're flexible on who that is.
What's the difference between a NEC 645 server room and a regular IT closet?
NEC 645 is an optional code section for "information technology equipment rooms" — rooms specifically designed and dedicated to IT equipment, with controlled HVAC, dedicated electrical, and a listed disconnect that shuts down both power and HVAC simultaneously. If you qualify under 645, some wiring methods and installation rules are relaxed. Most small-business server closets don't formally invoke 645 — they're just dedicated spaces with proper electrical and cooling. We'll tell you which category your buildout is in.
Do you handle commercial permit and inspection coordination?
Yes, as part of every commercial job. We pull the electrical permit under our license, schedule inspections at rough-in and final, and attend them. For TI work in strip centers or multi-tenant buildings, we also coordinate with the property's electrical setup and the landlord where our work touches shared infrastructure.
What kind of warranty do you offer on commercial work?
Our workmanship is warrantied — if something we installed fails because of how we installed it, we come back and fix it. The equipment itself (sauna heaters, POS systems, server hardware) carries its own manufacturer warranty. We hand off as-built documentation at closeout so you have a clear record of what was installed, where, and to what spec.
We serve Salt Lake County, Utah County, Wasatch County, Davis County from our Springville base. See all service areas →
Other things we handle.
Need an electrician for your Utah home?
Panel upgrades, EV chargers, generators, aluminum wiring, remodels, and everything in between — from a licensed, family-run team that takes the time to explain what we’re doing.



